Chine Bande d'enveloppe de tuyau de ruban anti-corrosif de tuyau de polyéthylène pour le pipeline en acier Fabricants

toutes catégories

nouveaux produits

Accueil > Liste de Produits > Revêtement de tuyau en caoutchouc butyle > Ruban anti-corrosion de tuyau > Bande d'enveloppe de tuyau de ruban anti-corrosif de tuyau de polyéthylène pour le pipeline en acier

Bande d'enveloppe de tuyau de ruban anti-corrosif de tuyau de polyéthylène pour le pipeline en acier

Description du produit

Bande anti-corrosive de tuyau de ruban de polyéthylène pour le tuyau en acier \ n \ n Description de produit \ n \ n I. Description: Le ruban anti-corrosif de tuyau est système de revêtement de bande appliqué à froid pour la protection anticorrosive de pétrole, gaz, pétrochimique et Eaux usées Conduites souterraines ou aériennes. Le ruban anti-corrosion doit être appliqué après l'apprêt et avant le ruban de couche extérieure à la main ou avec une banderoleuse. \ N \ n II.Structure \ n La spécification du tuyau anti-corrosion - Ruban de corrosion composé de deux couches, d'une couche adhésive et d'un film protecteur. Adhésif: caoutchouc butyle. Couche externe: Mélange spécial de polyéthylène stabilisé. III. Caractéristiques. Excellente adhérence sur les tuyaux et sur soi. Peut être appliqué sur Large plage de température \ n Bonne conformabilité et uniformité uniforme de l'épaisseur \ n Application facile sans équipement spécial \ n Compatible avec les revêtements de tuyaux communs \ n Excellente résistance au décollement cathodique \ n Conforme aux normes ASTM D 1000, EN 12068, AWWA C214, C209 et autres norme internationale \ n C ancien appliqué \ n \ n \ n IV. Propriétés physiques: \ n Pipe Anti-Corrosion Tape \ n \ n

Type	T-150	T-165	T-180
Total thickness (mm)	0.51	0.65	0.75
Polyethylene Film (mm)	0.31	0.37	0.41
Synthetic Adhesive (mm)	0.20	0.28	0.34
Elongation	≥400%
Tensile Strength (N/cm)	55	60	63
Peel Adhesion to Primed Pipe (N/cm)	25	30	33
Dielectric Strength(KV)	35	45.8	48
Cathodic Disbondment	0.24 in radius 6.4 mm
Volume Resistivity	2.5×10¹²ohm.m
Water Vapor Transmission Rate	≤0.1gm/m²/24h
Water Absorption Rate	<0.06%
Application Temperature	-10°c to 60°c
Max Serve Temperature	-40°c to 80°c
Color	Black
Available Roll Size (width×length)	2” to 36” ×50 to 900mm
Available Roll Length	10-300m

\ n Produits de vente à chaud


Pipeline Anti-corrosion Tape	Mechanical Protection Tape

Polyethylene Bitumen Tape	Viscoelastic Tape

\ n \ n

\ n

\ n \ n

1.Brand : XUNDA brand 2.Material: Polydethyelne and butyl rubber 3. Thickness: 15 mils to 40 mils 4. Width: 50 mm to 1000 mm 5.Length:10 m to 1800 meter 6.Main Customer:BGSL,SSGC,NIGC and so on 7.Industry Experience: more than 13 years 8.Biggest manufacture in China 9.proportion of exportation:more than 67% 10. Production ability: 10-15 ton per day 11.Accept OEM

1.Brand : XUNDA brand

2.Material: Polydethyelne and butyl rubber

3. Thickness: 15 mils to 40 mils

4. Width: 50 mm to 1000 mm

5.Length:10 m to 1800 meter

6.Main Customer:BGSL,SSGC,NIGC and so on

7.Industry Experience: more than 13 years

8.Biggest manufacture in China

9.proportion of exportation:more than 67%

10. Production ability: 10-15 ton per day

11.Accept OEM

\ n \ n \ n \ n

Description	Polyethylene butyl Pipe Wrap tape is a synthetic rubber-based material extruded into a soft permanently elastic strip, available in a roll form. The tape possesses high levels of surface tack and performs at a wide range of temperatures -T100 Inner layer wrap tape -T200 outer layer wrapping tape -T300 joint wrap tape
Usage	l Special for Oil ,Gas ,Water pipeline outer space corrosion prevent l Repair of damaged factory applied corrosion protection and anticorrosion to pipe surface l Outlining weld beads and cut backs prior to wrapping bare-welded joints. l Outlining seams on spiral and seam welded pipe.
Features & Benefits	l Excellent adhesion to a wide range of industries, steel piping. l Effortlessly applied with no special equipment (mouldable by hand). l Compatible with common pipe coatings l Endures extremes of heat and cold. l Excellent resistance to cathodic disbondment. l High water and vapour impermeability. l Complies with ISO,DIN30672,AWWAC214 209,ASTMD1000.EN12068
Main market	Iran,UAE,Iraq,Kuwait,Turkey,Egypt,Libya,Ukraine,Russia,Bengal,Pakistan, Uzbekistan,India,Australia,Indonesia,Kazakhstan, Ecuador,Venezuela,Bolivia,Argentina, Uruguay,Malaysia and so on.
Material:	Butyl rubber adhesive , bitumen/asphalt
Material:	PE,PVC, ALUMINUM backing film

\ n

\ n \ n

\ n \ n \ n \ n

\ n \ n

1 Rust Removal Steel Surface needs treating. Its quality shall reach Sa2 or St3 grade as prescribed in GB8923-88 Pre-paint Steel Surface Rust Grade and Rust-removal Grade, and it shall be dust-free. 2 Priming Primer shall be stirred well before painting. An even film of primer is painted on the steel surface that is rust-removed completely and dust-free. After the primer dries up (one may feel no sticky). The steel pipe can be wrapping with tape (it usually takes 3 to 5 minutes). The primer dosage usually amounts to 80 to 100g / m². 3 Inner Tape (Anti corrosion Tape) & Outer Tape (Protection Tape) Wrapping The steel pipe that is painted with primer is wrapping with tape by means of suitable devices or tools as per joint needs, and wraps the inner tape and then wraps the outer tape. Tape tensibility can be 10 to 20 N / cm. The overlapped length between beginning and end of an adhesive tape shall be no less than 1/4 circumference of the steel pipe and the total length of adhesive tape shall be no less than 100mm. each film shall be paralleled, and must not be twisted and rumpled.

1 Rust Removal

Steel Surface needs treating. Its quality shall reach Sa2 or St3 grade as prescribed in GB8923-88 Pre-paint Steel

Surface Rust Grade and Rust-removal Grade, and it shall be dust-free.

2 Priming

Primer shall be stirred well before painting. An even film of primer is painted on the steel surface that is rust-removed

completely and dust-free. After the primer dries up (one may feel no sticky). The steel pipe can be wrapping with tape

(it usually takes 3 to 5 minutes). The primer dosage usually amounts to 80 to 100g / m².

3 Inner Tape (Anti corrosion Tape) & Outer Tape (Protection Tape) Wrapping

The steel pipe that is painted with primer is wrapping with tape by means of suitable devices or tools as per joint needs,

and wraps the inner tape and then wraps the outer tape. Tape tensibility can be 10 to 20 N / cm. The overlapped length

between beginning and end of an adhesive tape shall be no less than 1/4 circumference of the steel pipe and the total

length of adhesive tape shall be no less than 100mm. each film shall be paralleled, and must not be twisted and rumpled.

\ n

\ n \ n \ n \ n \ n \ n

\ n \ n

\ n \ n \ n

Payment:	T/T , L/C,Western Union,Money Gram,Cash
MOQ:	300 rolls
Shipment port	Qingdao or Shanghai port
Package:	12 rolls/carton ,6 rolls/carton ,4 rolls/carton ,depend on your order size
	20 inch container could load about 16 Tons 40 inch container could load about 23 Tons
Sample leading time:	about 2 days in the free season,may be 4 days in the busy season.
Delivery time:	10 days after the order confirmed,and it depends on the quantity of the order.
Brands:	OEM or ODM, we can provide as your requirements, including your design/size/material/weight/Logo/package and so on.
Ordering Information	Tape Coatings are available in roll form.Ordering Example: T100-20 WHT6X100FT 3’’

\ n \ n \ n \ n

1.Experience QC department.
2.Top one-stop after-sale service.
3.Advance automatic imported machines
4.Outstanding and professional team
5. The most competitive price
6.Custom-design according to your favour.

1.Experience QC department.

2.Top one-stop after-sale service.

3.Advance automatic imported machines

4.Outstanding and professional team

5. The most competitive price

6.Custom-design according to your favour.

\ n \ n Contact